BVMI Nuclear Bellows Back to Top

DCL Markets

Market Data Download

Manifolds Download

Cartridge Valves

Cartridge Valves
Download

Cartridge Valves

Download

BVMI Download

LNG Gas Supply System Download
VALVE TECHNICAL DATA SHEET HIGH TEMPERATURE BELLOWS SEALED VALVE SERIES 4

Class 600 Bellows Sealed Globe Valve, Conventional Bore, Outside Screw and Yoke, Non-rising Handwheel, Bolted Bonnet. Available with Integral Hard Faced Seat or Screwed in Stainless Steel Seat Valve can be supplied with Actuator - Electric or Pneumatic. Buttweld end connections shown, also available as screwed, socket weld, Flanged or special connection.

ASME III option available.

Straight Pattern shown, also available as Angle pattern and Oblique pattern.

Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. Shown are the maximum ratings for socket weld, buttweld and screwed.

Materials can be changed to customer specifications.

There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425℃. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Service Temperature ℃ Service Pressure bar g
38 103.4
50 101.6
100 94.2
200 79.6
300 70.6
400 65.7
500 63.4
600 49.8
700 22.8
800 8.8
816 7.2
Dimensions
Valve Size
DN
Dim
A mm
Dim
B mm
Dim
C mm
Weight
Kg
Cv
IGPM
DN8 108 241 100 9 1.7
DN15 108 241 100 9 2.45
DN20 117 241 100 9 2.45
DN25 127 254 100 9.6 5.8
DN40 165 368 150 24 12.4
DN50 203 400 150 25 18.5
Material Specification
Body Stainless Steel Valve
St.St. ASTMA182
Bonnet F316H St.St. ASTM
Seat A182 F316H
Disk Integral Hard Faced
Stem St. St. - Hard Faced
Bellows St.St. ASTMA182 F316H
Back up Incolloy 800H or
Gland Yoke 800HT Exfoliated
Bush Graphite Aluminium
BELLOWS SEALED CARTRIDGE VALVE - MANIFOLD Series 34

Class 600 Bellows Sealed Globe Valve, Conventional Bore, Outside Screw and Yoke, Non-rising Handwheel, Bolted Bonnet. To BSEN15761 or Nuclear Class to ASME III available.

Valve can be supplied with actuation - Electric or Pneu- matic plus controls.

Extended spindle versions also available.

Manifold Block designed to suit requirements, distribution blocks, double block and bleed, reducing stations.

Valve type and numbers to suit requirements.

Cartridge Valve, seat and all seals are removed with the top assembly. This leaves only body left in line.

Maintenance time reduced significantly. Increases safety, no danger of seals being lost down line or seat not being fitted.

Suitable for High/Low Temperature / Extreme duties

Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials.

Valve design suitable for temperature upto 700 ℃.

Materials can be changed to customer specifications.

6 Valve Distribution Block

3 Valve Distribution Block

Material Specification
Body St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307)/ ASME SA182F304L
Bonnet St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307)/ ASME SA182F304L
Seat St.St. BSEN 10088-3 1.4307/ ASME SA479 F304L
Seat Seal Perlast or Kalrez or Stainless Steel Seal
Disk St.St. BSEN 10088-3 1.4307/ ASME SA479 F304L
Stem St.St. BSEN 10088-3 1.4307/ ASME SA479 F304L
Bellows St.St. Type 316L
Back up Gland Graphite
VALVE TECHNICAL DATA SHEET BELLOWS SEALED CARTRIDGE VALVE Series 34

Class 600 Bellows Sealed Globe Valve, Conventional Bore, Outside Screw and Yoke, Non-rising Handwheel, Bolted Bonnet. To BSEN15761 or Nuclear Class to ASME III available Valve can be supplied with actuation - Electric or Pneumatic plus controls.

Extended spindles alao available

Buttweld end connections shown, also available as screwed, socket weld, Flanged or special connection or Manifold blocks

Cartridge Valve, seat and all seals are removed with the top assembly.

This leaves only body left in line.

Maintainence time reduced significantly. Increases safety, no danger of seals being lost down line or seat not being fitted.

Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. Valve design suitable for temperature upto 608℉. Materials can be changed to customer specifications.

Dimensions
Valve Size
DN
Dim
A mm
Dim
B mm
Weight
Kg
Cv
IGPM
DN8/1/4 " 4.25 " 9.55 " 19.8 1.7
DN15/1/2" 19.8 2.45
DN20/3/4" 4.25" 9.55" 19.8 2.45
DN25/1" 4.6" 9.55" 21.2 5.8
DN40/ 1/2" 5" 10.10" 52.9 12.4
DN50/2" 6.5" 14.5" 55.1 18.5
DN80/3" 8" 15.75" 445 37
DN100/4" 14" 19.7" 529 76
DN150/6" 16" 20.50" 613 260
Material Specification
Body St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307)/ ASME SA182F304L
Bonnet St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307)/ ASME SA182F304L
Seat St.St. BSEN 10088-3 1.4307/ ASME SA479 F304L
Seat Seal Perlast or Kalrez Seal
Disk St.St. BSEN 10088-3 1.4307/ ASME SA479 F304L
Stem St.St. BSEN 10088-3 1.4307/ ASME SA479 F304L
Bellows St.St. Type 316L
Back up Gland Graphite
VALVE TECHNICAL DATA SHEET BELLOWS SEALED CARTRIDGE VALVE SERIES 34

Class 600 Bellows Sealed Globe Valve to BS5352/ANSI B16.34, Conventional Bore, Outside Screw and Yoke, Non-rising Handwheel, Hermetically Seal Welded Bonnet.

Available with Integral Hard Faced Seat or Screwed in Stainless Steel Seat

Valve can be supplied with Actuator - Electric or Pneumatic.

Locking Device, Interlocks, Extended Spindle.

Buttweld end connections shown, also available as screwed, socket weld, Flanged or special connection

Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. Shown are the maximum ratings for socket weld, buttweld and screwed ends to BS5352. Pressure/ Temperature rating to ANSI B16.34 differ.

Materials can be changed to customer specifications.

There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not rec- ommended for use above 425℃.

If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Service Temperature ℃ Service Pressur e Bar g
-30 to +38 99
50 98
100 96
150 94
200 91
250 87
300 79
350 71
400 63
450 55
500 34
Dimensions
Valve Size
DN
Dim
A in
Dim
B in
Dim
C in
Weight
lb
Cv
IGPM
DN8/1/4 " 108 241 100 9 1.7
DN15/1/2 " 108 241 100 9 2.45
DN20/3/4" 117 241 100 9 2.45
DN25/1" 127 254 100 9.6 5.8
DN40/11/2 165 368 150 24 12.4
DN50 203 400 150 25 18.5
Material Specification
Carbon Steel Valve Stainless Steel Valve
Body C.St. ASTM A105 St.St. Type 316
Bonnet C.St. ASTM A105 St.St. Type 316
Seat St.St. Type 410, Type 316 or Integral Stellite HF St.St. Type 410, Type 316 or Integral Stellite HF
Disk St.St. Type 410, Type 316 or Stellite HF St.St. Type 410, Type 316 or Stellite HF
Stem St. St. Type 316 St. St. Type 316
Bellows St. St. Type 316 St. St. Type 316
Back up Gland Exfoliated Graphite Exfoliated Graphite
Yoke Bush Aluminium Bronze Aluminium Bronze
VALVE TECHNICAL DATA SHEET BELLOWS SEALED VALE SERIES 34

Class 800 Bellows Sealed Globe Valve to BS5352, Conventional Bore, Outside Screw and Yoke, Non-rising Handwheel, Bolted Bonnet.

Available with Integral Hard Faced Seat or Screwed in Stainless Steel Seat

Valve can be supplied with Actuator - Electric or Pneumatic.

Buttweld end connections shown, also available as screwed, socket weld, Flanged or special connection.


Nuclear Versions to ASME III available.

Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. Shown are the maximum ratings for socket weld, buttweld and screwed ends to BS5352

Materials can be changed to customer specifications.

There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not rec- ommended for use above 425 ℃. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Service Temperature ℃ Service Pressure Bar g
-30 to +38 99
50 98
100 96
150 94
200 91
250 87
300 79
350 71
400 63
450 55
500 34
Dimensions
Valve Size
DN
Dim
A in
Dim
B in
Dim
C in
Weight
lb
Cv
IGPM
DN8/1/4 " 4.25 9.50 3.95 19.8 1.7
DN15/1/2 " " " " 19.8 2.45
DN20/3/4" 4.25 9.50 3.95 19.8 2.45
DN25/1" 4.60 9.50 3.95 21.2 5.8
DN40/11/2 5.00 10.00 3.95 52.9 12.4
" 6.50" 14.50" 5.90" 55.1 18.5
Material Specification
Carbon Steel Valve Stainless Steel Valve
Body C.St. ASTM A105 St.St. Type 316L
Bonnet C.St. ASTM A105 St.St. Type 316L
Seat St.St. Type 410 or Integral Stellite HF St.St. Type 410 or Integral Stellite HF
Disk St.St. Type 410, Type 316 or Stellite HF St.St. Type 410, Type 316 or Stellite HF
Stem St. St. Type 316L St. St. Type 316L
Bellows St. St. Type 316L St. St. Type 316L
Back up Gland Exfoliated Graphite Exfoliated Graphite
Yoke Bush Aluminium Bronze Aluminium Bronze
VALVE TECHNICAL DATA SHEET BELLOWS SEALED VALVE - NUCLEAR SERIES 34

Class 600 Bellows Sealed Globe Valve designed to ASME III, Conventional Bore, Outside Screw and Yoke, Non-rising Handwheel, Bolted Bonnet.

Seal Welded Bonnet version available.

Available with Integral Hard Faced Seat or Screwed in Stainless Steel Seat

Valve can be supplied with Actuator - Electric or Pneumatic.

Buttweld end connections shown, also available as screwed, socket weld, Flanged or special connection

Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials.

Materials can be changed to customer specifications.

There are temperature restrictions on some materials, ie. C.St. ASME SA105 is not recommended for use above 425℃. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Dimensions
Valve Size
DN
Dim
A in
Dim
B in
Dim
C in
Weight
lb
Cv
IGPM
DN8/1/4 " 4.25 9.50 3.95 19.8 1.7
DN15/1/2 " " " " 19.8 2.45
DN20/3/4 " 4.25 9.50 3.95 19.8 2.45
DN25/1" 4.60 9.50 3.95 21.2 5.8
DN40/11/2 5.00 10.00 3.95 52.9 12.4
" 6.50 14.50 5.90 55.1 18.5
Material Specification
Carbon Steel Valve Stainless Steel Valve
Body C.St. ASME SA105 St.St. ASME SA182 316L
Bonnet C.St. ASME SA105 St.St. ASME SA182 316L
Seat St.St. ASME SA564 630 or Integral Stellite HF St.St. ASME SA564 630 or Integral Stellite HF
Disk St.St. ASME SA564 630 or Stellite HF St.St. ASME SA564 630 or Stellite HF
Stem St. St. ASME SA479 316L St. St. ASME SA479316L
Bellows St. St. Type 316 St. St. Type 316
Back up Gland Exfoliated Graphite Exfoliated Graphite
VALVE TECHNICAL DATASHEET BELLOWS SEALED CARTRIDGE VALVE - EXTREME SERIES 4

Class 600 Bellows Sealed Globe Valve, Conventional Bore, Outside Screw and Yoke, Non-rising Handwheel, Bolted Bonnet. To BSEN15761 or Nuclear Class to ASME III available Valve can be supplied with actuation - Electric or Pneumatic plus controls.

Extended spindles alao available

Buttweld end connections shown, also available as screwed, socket weld, Flanged or special connection or Manifold blocks

Cartridge Valve, seat and all seals are removed with the top assembly.

This leaves only body left in line.

Maintainence time reduced significantly. Increases safety, no danger of seals being lost down line or seat not being fitted.

Class 600 Bellows Sealed Globe Valve, Conventional Bore, Outside Screw and Yoke, Non-rising Handwheel, Bolted Bonnet. To BSEN15761 or Nuclear Class to ASME III available Valve can be supplied with actuation - Electric or Pneumatic plus controls.

Extended spindles alao available

Buttweld end connections shown, also available as screwed, socket weld, Flanged or special connection or Manifold blocks Cartridge Valve, seat and all seals are removed with the top assembly.

This leaves only body left in line. Maintainence time reduced significantly. Increases safety, no danger of seals being lost down line or seat not being fitted.

Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. Valve design suitable for temperature upto 1290℉. Materials can be changed to customer specifications.

Dimensions
Valve Size
DN
Dim
A mm
Dim
B mm
Weight
Kg
Cv
IGPM
DN8/1/4 " 4.25 " 9.55 " 19.8 1.7
DN15/1/2" " " 19.8 2.45
DN20/3/4" 4.25" 9.55" 19.8 2.45
DN25/1" 4.6" 9.55" 21.2 5.8
DN50/2" 6.5" 14.5" 55.1 18.5
DN80/3" 8" 15.75" 445 37
DN100/4" 14" 19.7" 529 76
DN150/6" 16" 20.50" 613 260
Material Specification
Body St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307)/ ASME SA182F304L
Bonnet St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307)/ ASME SA182F304L
Seat St.St. BSEN 10088-3 1.4307/ ASME SA479 F304L
Seat Seal Stainless Steel
Disk St.St. BSEN 10088-3 1.4307/ ASME SA479 F304L
Stem St.St. BSEN 10088-3 1.4307/ ASME SA479 F304L
Bellows St.St. Type 316L
Back up Gland Graphite
VALVE TECHNICAL DATASHEET HIGH TEMPERATURE BELLOWS SEALED VALVE SERIES 34
Series 34 High Temperature Bellows Sealed Valve

Class 800 Bellows Sealed Globe Valve to BS5352, Conventional Bore, Outside Screw and Yoke, Non-rising Handwheel, Bolted Bonnet.

Available with Integral Hard Faced Seat or Screwed in Stainless Steel Seat

Valve can be supplied with Actuator - Electric or Pneumatic.

Buttweld end connections shown, also available as screwed, socket weld, Flanged or special connection.


Nuclear Versions to ASME III available.

Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. Shown are the maximum ratings for socket weld, buttweld and screwed ends to BS5352

Materials can be changed to customer specifications.

There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not rec- ommended for use above 425 ℃. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Class 600 Bellows Sealed Globe Valve, Conventional Bore, Outside Screw and Yoke, Non-rising Handwheel, Bolted Bonnet.

Available with Integral Hard Faced Seat or Screwed in Stainless Steel Seat Valve can be supplied with Actuator - Electric or Pneumatic.

Buttweld end connections shown, also available as screwed, socket weld, Flanged or special connection. ASME III option available.

Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. Shown are the maximum ratings for socket weld, buttweld and screwed ends to BS5352

Materials can be changed to customer specifications.

There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not rec- ommended for use above 425℃. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media

Service Temperature
Service Pressure
psi g
100 1440
200 1240
300 1120
400 1030
500 955
600 905
700 865
900 790
1100 645
1300 275
1500 85
Dimensions
Valve Size
DN
Dim
A in
Dim
B in
Dim
C in
Weight
lb
Cv
IGPM
DN8/1/4 " 4.25 9.50 3.95 19.8 1.7
DN15/1/2 " " " " 19.8 2.45
DN20/3/4 " 4.25 9.50 3.95 19.8 2.45
DN25/1" 4.60 9.50 3.95 21.2 5.8
DN40/11/2 5.00 10.00 3.95 52.9 12.4
" 6.50 14.50 5.90 55.1 18.5
Material Specification
Stainless Steel Valve
Body St.St. ASTM A182 F316H
Bonnet St.St. ASTM A182 F316H
Seat Integral Hard Faced
Disk St. St. - Hard Faced
Stem St.St. ASTM A182 F316H
Bellows Incolloy 800H or 800HT
Back up Gland Exfoliated Graphite
Yoke Bush Aluminium Bronze
VALVE TECHNICAL DATA SHEET BBOLTED BONNET VALVE - STRAIGHT PATTERN SERIES 34A

Class 800/900/1500 bellows sealed globe valve to BS5352, standard bore, outside screw and yoke, non-rising handwheel, bolted bonnet.

Available with integral hard faced seat or screwed in stainless steel seat.

Valve can be supplied with actuator - electric or pneumatic.

Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection.

Nuclear versions to ASME III available.?

Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials. Shown are the maximum ratings for socket weld, butt weld and screwed ends to BS5352.

Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St.

ASTM A105 is not recommended for use above 425 oC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Class 800
Service Service ℃
Class 800
Temperature Pressure Bar g
-38 to +38 99
50 98
100 96
150 94
200 91
250 87
300 79
350 71
400 63
450 55
500 34
Dimensions (typical)
Class 800 Class 900/1500
Valve Size
DN
Dim
A mm
Dim
B mm
Dim
C mm
Weight
Kg
Cv
UK
Gal/min
Dim A
mm
Dim B
mm
Dim C
mm
Weight
Kg
Cv
UK
Gal/min
DN6 108 241 100 9 1.7 216 321 150 12 1.7
DN15 108 241 100 9 2.45 216 321 150 12 2.45
DN20 117 241 125 9 2.45 229 321 175 12 2.45
DN25 127 254 125 9.6 5.8 254 384 175 15 5.8
DN40 165 368 175 24 12.4 305 458 225 30 12.4
DN50 203 400 200 25 18.5 368 530 350 35 18.5
Material
Component Carbon Steel Valve Stainless Steel Valve
Body C.St. ASTM A105 St.St. Type 316L
Bonnet C.St. ASTM A105 St.St. Type 316L
Seat St.St. Type 410 or integral Stellite HF St.St. Type 410 or integral Stellite HF
Disk St.St. Type 410 or Stellite HF St.St. Type 410 or Stellite HF
Stem St.St. Type 316L St.St. Type 316L
Bellows St.St. Type 316L St.St. Type 316L
Back up Gland Exfoliated graphite Exfoliated Graphite
Yoke Bush Aluminium Bronze Aluminium Bronze
VALVE TECHNICAL DATA SHEET BOLTED BONNET VALVE - OBLIQUE PATTERN SERIES 34B

Class 600/900/1500 bellows sealed globe valve, standard bore, outside screw and yoke, non-rising handwheel, bolted bonnet. To BSEN15761 or nuclear class to ASME III available.

Valve can be supplied with actuation - electric or pneumatic plus controls. Extended spindles also available.

Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection or manifold blocks.

Cartridge valve, version also available - seat and all seals are removed with the top assembly. This leaves only the body left in line. Maintenance time reduced significantly. Increases safety, no danger of seals being lost down line or seat not being fitted.

Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials. Valve design suitable for temperatures up to 320 ℃. Materials can be changed to customer specifications.

Dimensions
Valve Size
DN
Dim
A mm
Dim
B mm
Weight
Kg
Cv
UKGPM
6 229 242 13 2
15 229 242 13 5.8
20 229 245 13 5.8
25 254 260 15.5 11
40 305 350 35 30
50 368 420 40 54
80 381 540 250 153
100 457 562 295 267
150 610 820 320 690
Material
Component Material
Body St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307) / ASME SA182 F304L
Bonnet St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307) / ASME SA182 F304L
Seat St.St. BSEN 10088-3 1.4307 / ASME SA479 304L / HF
Seat Seal Stainless steel / Graphite
Disk St.St. BSEN 10088-3 1.4307 / ASME SA479 304L / HF
Stem St.St. BSEN 10088-3 1.4307 / ASME SA479 304L
Bellows St.St. Type 316L
Back up Gland Graphite
VALVE TECHNICAL DATA SHEET BOLTED BONNET VALVE - ANGLE PATTERN SERIES 34C

Class 800/900/1500 bellows sealed globe valve to BS5352, standard bore, outside screw and yoke, non-rising handwheel, bolted bonnet.

Available with integral hard faced seat or screwed in stainless steel seat.

Valve can be supplied with actuator - electric or pneumatic. Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection.

Nuclear versions to ASME III available.

Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials.

Materials can be changed to customer specifications.

There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425 ℃. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

DN50 102 400 150 25 29.6 184 530 290 35 29.6
Dimensions (typical)
Class 800 Class 900/1500
Valve Size
DN
Dim
A mm
Dim
B mm
Dim
C mm
Weight
Kg
Cv
UK
Gal/min
Dim A
mm
Dim B
mm
Dim C
mm
Weight
Kg
Cv
UK
Gal/min
DN6 57 241 100 9 2.7 108 321 150 12 2.7
DN15 57 241 100 9 3.9 108 321 150 12 3.9
DN20 64 241 100 9 3.9 114 321 150 12 3.9
DN25 70 254 100 9.6 9.2 127 384 150 15 9.2
DN40 83 368 150 24 19.8 152 458 200 30 19.8
DN50 102 400 150 25 29.6 184 530 290 35 29.6
Material
Component Carbon Steel Valve Stainless Steel Valve
Body C.St. ASTM A105 St.St. Type 316L
Bonnet C.St. ASTM A105 St.St. Type 316L
Seat St.St. Type 410 or integral Stellite HF St.St. Type 410 or integral Stellite HF
Disk St.St. Type 410 or Stellite HF St.St. Type 410 or Stellite HF
Stem St.St. Type 316L St.St. Type 316L
Bellows St.St. Type 316L St.St. Type 316L
Back up Gland Exfoliated graphite Exfoliated Graphite
Yoke Bush Aluminium Bronze Aluminium Bronze
VALVE TECHNICAL DATA SHEET SEAL WELDED BONNET VALVE - STRAIGHT PATTERN SERIES 35A

Seal Welded Bonnet Valve - Straight Pattern. Standard Bore, Outside Screw and Yoke, Non-rising handwheel, Seal Welded Bonnet. To ANSI B16.34 or Nuclear Class to ASME III

Available with Integral Hard Faced (Stellite 6 or Colomonoy 5) Seat or Screwed in Stainless Steel Seat

Valve can be supplied with Actuator - Electric or Pneumatic.

Buttweld end connections shown, also available as screwed, socket weld, flanged or special connection

Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials.

Materials can be changed to customer specifications.

There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425 ℃.

If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

DN65/DN80/DN100 normally cast body and bonnet. Forged available.

Dimensions (typical)
Class 150/300/600 Class 900/1500
Valve Size
DN
Dim
A mm
Dim
B mm
Dim
C mm
Weight
Kg
Cv
UK
Gal/min
Dim A
mm
Dim B
mm
Dim C
mm
Weight
Kg
Cv
UK
Gal/min
DN6 165 243 100 16 1.0 216 261 150 12 1.0
DN15 165 243 100 16 1.8 216 261 150 12 1.6
DN20 190 243 100 16 4.0 229 261 150 12 2.9
DN25 216 256 125 20 6.9 254 294 150 14 5.0
DN40 241 368 150 33 17.4 305 398 200 28 14.5
DN50 102 400 150 25 29.6 184 530 290 35 29.6
DN65 330 450 300 220 46.0 419 500 300 180 37.0
DN80 356 500 300 260 70.0 381/470 560 300 200 62.0
DN100 432 521 300 350 128.0 457/546 590 300 290 113.0
Material
Component Carbon Steel Valve Stainless Steel Valve
Body & Bonnet C.St. ASME SA350 LF2 or C.St. ASME SA352 LCB St.St. ASME SA182 F316L or St.St. ASME SA351 CF3M
Seat Integral Hard Facing Integral Hard Facing
Disk St.St. Type 316L with Hard Facing St.St. Type 316L with Hard Facing
Stem St. St. ASME SA564 630 H1075 St. St. ASME SA564 630 H1075
Bellows Inconel 600/625 Inconel 600/625
Gland Exfoliated Graphite Exfoliated Graphite
Bush Aluminium Bronze Aluminium Bronze
VALVE TECHNICAL DATA SHEET SEAL WELDED BONNET VALVE - OBLIQUE PATTERN SERIES 3AB

Seal Welded Bonnet Valve - Oblique Pattern. Standard Bore, Outside Screw and Yoke, Non-rising handwheel, Seal Welded Bonnet.

Available with Integral Hard Faced Seat to offer increased resistance against corrosion.

Valve can be supplied with Actuator - Electric or Pneumatic.

Buttweld end connections shown, also available as screwed, socket weld, flanged or special connection

Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials.

Shown are the maximum ratings for socket weld, butt weld and screwed ends to BS5352.

Temperature ℃ Pressure Bar g
-30 to 38 99
50 98
100 96
150 94
200 91
250 87
300 79
350 71
400 63
450 55
500 34
Dimensions (typical)
Class 800
Valve Size
DN
Dim
A mm
Dim
B mm
Dim
C mm
Weight
Kg
Cv
UK
Gal/min
DN6 154 210 95 9 4.4
DN15 154 210 95 10 4.4
DN20 154 210 95 11 4.4
DN25 154 210 95 11 9.1
DN40 224 325 165 24 27.5
DN50 274 325 130 25 40

Dimensions are subject to confirmation.

Drawings with confirmed dimensions can be supplied at time of order.

Materials can be changed to customer specifications.

There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425℃.

If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Material
Component Carbon Steel Valve Stainless Steel Valve
Body & Bonnet C.St. ASTM A105 St.St. BS1503 304S11
Seat St.St. Type 410 or Integral Stellite Hard Facing St.St. Type 410 or Integral Stellite Hard Facing
Disk St.St. Type 410 or Stellite Hard Facing St.St. Type 410 or Stellite Hard Facing
Stem St. St. Type 304 St. St. Type 304
Bellows St. St. Type 304 St. St. Type 304
Gland Exfoliated Graphite Exfoliated Graphite
Bush Aluminium Bronze Aluminium Bronze
VALVE TECHNICAL DATA SHEET SEAL WELDED BONNET VALVE - ANGLE PATTERN SERIES 35C

Seal Welded Bonnet Valve - Angle Pattern. Standard Bore, Outside Screw and Yoke, Non-rising handwheel, Seal Welded Bonnet.

To ANSI B16.34 or Nuclear Class to ASME III

Available with Integral Hard Faced (Stellite 6 or Colomonoy 5) Seat or Screwed in Stainless Steel Seat

Valve can be supplied with Actuator - Electric or Pneumatic.

Buttweld end connections shown, also available as screwed, socket weld, flanged or special connection

Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials.

Materials can be changed to customer specifications.

There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425℃.

If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

DN65/DN80/DN100 normally cast body and bonnet. Forged available.?

Dimensions (typical)
Class 150/300/600 Class 900/1500
Valve Size
DN
Dim
A mm
Dim
B mm
Dim
C mm
Weight
Kg
Cv
UK
Gal/min
Dim A
mm
Dim B
mm
Dim C
mm
Weight
Kg
Cv
UK
Gal/min
DN6 57 243 100 16 2.7 108 261 150 12 2.7
DN15 57 243 100 16 3.9 108 261 150 12 3.9
DN20 64 243 100 16 3.9 114 261 150 12 3.9
DN25 70 256 125 20 9.2 127 294 150 14 9.2
DN40 83 368 150 33 19.8 152 398 200 28 19.8
DN50 102 400 200 39 29.6 184 440 250 30 29.6
DN65 108 450 300 220 73 210 500 300 180 60
DN80 121 500 300 260 110 235 560 300 200 100
DN100 146 521 300 350 204 273 590 300 290 180
Material
Component Carbon Steel Valve Stainless Steel Valve
Body & Bonnet C.St. ASME SA350 LF2 or C.St. ASME SA352 LCB St.St. ASME SA182 F316L or St.St. ASME SA351 CF3M
Seat Integral Hard Facing Integral Hard Facing
Disk St.St. Type 316L with Hard Facing St.St. Type 316L with Hard Facing
Stem St. St. ASME SA564 630 H1075 St. St. ASME SA564 630 H1075
Bellows Inconel 600/625 Inconel 600/625
Gland Exfoliated Graphite Exfoliated Graphite
Bush Aluminium Bronze Aluminium Bronze
VALVE TECHNICAL DATA SHEET SEAL WELDED BONNET VALVE - ANGLE PATTERN SERIES 35C

Class 900/1500 bellows sealed globe valve, standard bore, outside screw and yoke, bolted and lip-seal welded bonnet. ASME III option available.

Secondary gland in the event of bellows failure. Available with integral hard faced seat to offer increased resistance against erosion

Valve can be supplied with manual operation or actuated - electric or pneumatic. Manual valve and electrically actuated valve shown.

Class 900
Manually Operated Electrically Operated
Size
DN
Dim A
mm
Dim B
mm
Weight
Kg
Dim D
mm
Dim E
mm
Weight
Kg
Cv
UKGPM
6 216 320 13.8 520 216 Please ask for details 1.0
15 216 320 13.8 520 216 1.8
20 229 320 13.8 520 229 4.0
25 254 320 13.8 520 254 6.9
40 305 382 24.1 570 305 17.4
50 368 406 46.8 595 368 31.0
65 419 406 46.8 595 419 46.0
80 381 548 97.7 730 381 70.0
100 457 579 183 755 457 128.0
Class 1500
Manually Operated Electrically Operated
Size
DN
Dim A
mm
Dim B
mm
Weight
Kg
Dim D
mm
Dim E
mm
Weight
Kg
Cv
UKGPM
6 216 305 17.2 TBA 216 Please ask for details 1.0
15 216 305 17.2 TBA 216 1.6
20 229 305 18.6 TBA 229 2.9
25 254 311 19.5 TBA 254 5.0
40 305 345 28.1 TBA 305 14.5
50 368 371 76.2 TBA 368 23.0
65 419 400 80.3 TBA 419 37.0
80 381 508 137 TBA 381 62.0
100 457 577 231 TBA 457 113.0
Material
Component 316 Stainless Steel 304 Stainless Steel
Body St.St. ASME SA182 F316 St.St. ASME SA182 F304
Bonnet St.St. ASME SA182 F316 St.St. ASME SA182 F304
Seat St.St. ASME SA479 316 or integral Stellite hard faced St.St. ASME SA479 304 or integral Stellite hard faced
Disk St.St. ASME SA479 316 or St.St. Type 316 hard faced St.St. ASME SA479 304 or St.St. Type 304 hard faced
Stem St.St. ASME SA479 316 St.St. ASME SA479 304
Bellows St.St. Type 316/316L St.St. Type 316/316L
Back up Gland Exfoliated Graphite Exfoliated Graphite
Yoke Bush Aluminium Bronze Aluminium Bronze

Valve shown is with a leak detection port, to provide early warning of any bellows failure.

Extended spindles, type and length are designed to suit customer requirements. Weights shown are without extended spindle. Pneumatically actuated valves are available.

VALVE TECHNICAL DATA SHEET SEAL WELDED BONNET VALVE - ANGLE PATTERN SERIES 35C

Class 900/1500 bellows sealed globe valve, standard bore, outside screw and yoke, bolted and lip-seal welded bonnet. ASME III option available.

Secondary gland in the event of bellows failure. Available with integral hard faced seat to offer increased resistance against erosion

Valve can be supplied with manual operation or actuated - electric or pneumatic. Manual valve and electrically actuated valve shown.

Class 900
Manually Operated Electrically Operated
Size
DN
Dim A
mm
Dim B
mm
Weight
Kg
Dim D
mm
Dim E
mm
Weight
Kg
Cv
UKGPM
6 288 245 13.8 551 288 Please ask for details 7
15 288 245 13.8 551 288 7
20 288 245 13.8 551 288 12.9
25 288 245 13.8 551 288 20.8
40 323 293 24.1 585 323 39
50 407 311 46.8 605 407 92
65 407 311 46.8 605 407 125
80 437 420 97.7 742 437 213
100 427 443 183 755 427 260
Class 1500
Manually Operated Electrically Operated
Size
DN
Dim A
mm
Dim B
mm
Weight
Kg
Dim D
mm
Dim E
mm
Weight
Kg
Cv
UKGPM
6 323 305 17.2 TBA 323 Please ask for details 7
15 323 305 17.2 TBA 323 7
20 323 305 18.6 TBA 323 12.9
25 407 311 19.5 TBA 407 20.8
40 407 345 28.1 TBA 407 39
50 437 371 76.2 TBA 437 92
65 437 400 80.3 TBA 437 125
80 508 508 137 TBA 508 213
100 508 577 231 TBA 508 260
Material
Component 316 Stainless Steel 304 Stainless Steel
Body St.St. ASME SA182 F316 St.St. ASME SA182 F304
Bonnet St.St. ASME SA182 F316 St.St. ASME SA182 F304
Seat St.St. ASME SA479 316 or integral Stellite hard faced St.St. ASME SA479 304 or integral Stellite hard faced
Disk St.St. ASME SA479 316 or St.St. Type 316 hard faced St.St. ASME SA479 304 or St.St. Type 304 hard faced
Stem St.St. ASME SA479 316 St.St. ASME SA479 304
Bellows St.St. Type 316/316L St.St. Type 316/316L
Back up Gland Exfoliated Graphite Exfoliated Graphite
Yoke Bush Aluminium Bronze Aluminium Bronze

Valve shown is with a leak detection port, to provide early warning of any bellows failure.

Extended spindles, type and length are designed to suit customer requirements. Weights shown are without extended spindle. Pneumatically actuated valves are available.

VALVE TECHNICAL DATA SHEET BOLTED/EDGE BONNET VALVE - ANGLE PATTERN SERIES 36C

Class 900/1500 bellows sealed globe valve, standard bore, outside screw and yoke, bolted and lip-seal welded bonnet. ASME III option available.

Secondary gland in the event of bellows failure. Available with integral hard faced seat to offer increased resistance against erosion

Valve can be supplied with manual operation or actuated - electric or pneumatic. Manual valve and electrically actuated valve shown.

Class 900
Manually Operated Electrically Operated
Size
DN
Dim A
mm
Dim B
mm
Weight
Kg
Dim D
mm
Dim E
mm
Weight
Kg
Cv
UKGPM
6 108 320 13.8 520 108 Please ask for details 7
15 108 320 13.8 520 108 7
20 114 320 13.8 520 114 12.9
25 127 320 13.8 520 127 20.8
40 152 382 24.1 570 152 39
50 184 406 46.8 595 184 92
65 210 406 46.8 595 210 125
80 190 548 97.7 730 190 213
100 229 579 183 755 229 260
Class 1500
Manually Operated Electrically Operated
Size
DN
Dim A
mm
Dim B
mm
Weight
Kg
Dim D
mm
Dim E
mm
Weight
Kg
Cv
UKGPM
6 108 305 17.2 TBA 108 Please ask for details 7
15 108 305 17.2 TBA 108 7
20 114 305 18.6 TBA 114 12.9
25 127 311 19.5 TBA 127 20.8
40 152 345 28.1 TBA 152 39
50 184 371 76.2 TBA 184 92
65 210 400 80.3 TBA 210 125
80 235 508 137 TBA 235 213
100 273 577 231 TBA 273 260
Material
Component 316 Stainless Steel 304 Stainless Steel
Body St.St. ASME SA182 F316 St.St. ASME SA182 F304
Bonnet St.St. ASME SA182 F316 St.St. ASME SA182 F304
Seat St.St. ASME SA479 316 or integral Stellite hard faced St.St. ASME SA479 304 or integral Stellite hard faced
Disk St.St. ASME SA479 316 or St.St. Type 316 hard faced St.St. ASME SA479 304 or St.St. Type 304 hard faced
Stem St.St. ASME SA479 316 St.St. ASME SA479 304
Bellows St.St. Type 316/316L St.St. Type 316/316L
Back up Gland Exfoliated Graphite Exfoliated Graphite
Yoke Bush Aluminium Bronze Aluminium Bronze

Valve shown is with a leak detection port, to provide early warning of any bellows failure.

Extended spindles, type and length are designed to suit customer requirements. Weights shown are without extended spindle. Pneumatically actuated valves are available.

CARTRIDGE VALVE TECHNICAL DATA SHEET
BELLOWS SEALED STOP AND STOP/CHECK VALVE SERIES 40A
103.4 Bar 1500 psi (Class 600)
Technical Data
Design SpecificationDEF STAN 02-375 and ANSI B16.34
Working Pressure 103.4 Bar / 1500 psi
Working Temperature Min -20 ℃/-4℉ - - Max 326 ℃/619℉
Applications    |    Medium Air, Oil, Gas, Water
Quality Assurance Level EN 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330 or MIL-STD-1622
Hydrostatic Test 156 Bar / 2262psi
Valve Closure Test 114 Bar / 1653psi
Shock QualificationTo be verified by test to customer’s requirements e.g. MIL-S-901D
Vibration QualificationTo be verified by test to customer's requirements e.g. MIL-STD-167-1
Leakage ClassBubble Tight as per ANSI Class VI
Valve Body Material Forged Stainless Steel type 316L, Super Austenitic type F44, Carbon Steel type A105 or Monel
Main Cartridge Components Material Stainless Steel type 316L, Super Austenitic type F44 or Monel
Bellows Material Stainless Steel type 316L, Inconel 600/625
Seals Material Perlast / Kalrez
Seat Material Stainless Steel type 316L, Super Austenitic type F44, Monel or PEEK
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASTM A193/ MIL-S-1222/Monel
Handwheel Material Aluminum, Stainless Steel or Iron
Connection Type Cartridge flanged to housing. Housing socket weld ends, buttweld ends or flanged
OVERALL DIMENSIONS (CARTRIDGE AND VALVE BODY)
Product
Designation
Estimated
Weight
Pipe Size CV
UK Gal/min / US Gal/min
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
S40A-15 7Kg/15.5lbs DN15 /1/2 " 2.45 / 2.94 108 / 4.26" 214 / 8.43" 108 / 4.26"
S50A-20 7Kg/15.5lbs DN20/3/4" 2.45 / 2.94 117 / 4.61" 214 / 8.43" 108 / 4.26"
S50A-25 8Kg/17.6lbs DN25 / 1" 5.8 / 6.96 127 / 5" 225 / 8.86" 108 / 4.26"
S50A-40 17Kg/37.5lbs DN40 /11/2" 12.4 / 14.9 165 / 6.5" 340 / 13.39" 115 / 4.53"
S40A-50 22Kg/48.5lbs DN50 / 2" 18.5 / 22.2 203 / 8" 350 / 13.78" 115 / 4.53"
S40A-80 62Kg/136.7lbs DN80 / 3" 37 / 44.4 318 / 12.52" 500 / 19.59" 142 / 5.59"
S40A-100 120Kg/264.5lbs DN100 / 4" 76 / 91.2 406 / 15.99" 521 / 20.52" 180 / 7.09"
S40A-150 170Kg/374.8lbs DN150 / 6" 260 / 312 559 / 22" 780 / 30.71" 220 / 8.66"
CARTRIDGE VALVE TECHNICAL DATA SHEET
BELLOWS SEALED STOP AND STOP/CHECK VALVE SERIES 40B
103.4 Bar 1500 psi (Class 600)
Technical Data
Design SpecificationDEF STAN 02-375 and ANSI B16.34
Working Pressure 103.4 Bar / 1500 psi
Working Temperature Min -20 ℃/-4℉ - - Max 326 ℃/619℉
Applications    |    Medium Air, Oil, Gas, Water
Quality Assurance Level EN 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330 or MIL-STD-1622
Hydrostatic Test 156 Bar / 2262psi
Valve Closure Test 114 Bar / 1653psi
Shock QualificationTo be verified by test to customer’s requirements e.g. MIL-S-901D
Vibration Qualification To be verified by test to customer’s requirements e.g. MIL-STD-167-1
Leakage Class Bubble Tight as per ANSI Class VI
Valve Body Material Forged Stainless Steel type 316L, Super Austenitic type F44, Carbon Steel type A105 or Monel
Main Cartridge Components Material Stainless Steel type 316L, Super Austenitic type F44 or Monel
Bellows Material Stainless Steel type 316L, Inconel 600/625
Seals Material Perlast / Kalrez
Seat Material Stainless Steel type 316L, Super Austenitic type F44, Monel or PEEK
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASTM A193/ MIL-S-1222/Monel
Handwheel Material Aluminum, Stainless Steel or Iron
Connection Type Cartridge flanged to housing. Housing socket weld ends, buttweld ends or flanged
OVERALL DIMENSIONS (CARTRIDGE AND VALVE BODY)
Product
Designation
Estimated
Weight
Pipe Size CV
UK Gal/min / US Gal/min
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
S40B-15 7Kg/15.5lbs DN15 /1/2 " 5.8 / 6.96 165 / 6.5" 180 / 7.09" 86 / 3.39"
S40B-20 7Kg/15.5lbs DN20/3/4" 5.8 / 6.96 190 / 7.48" 180 / 7.09" 86 / 3.39"
S40B-25 8Kg/17.6lbs DN25 / 1" 11 / 13.2 216 / 8.5" 190 / 7.48" 86 / 3.39"
S40B-40 19Kg/41.9lbs DN40 /11/2" 30 / 36 241 / 9.49" 260 / 10.24" 137 / 5.39"
S40B-50 22Kg/48.5lbs DN50 / 2" 54 / 64.8 292 / 11.5" 280 / 11.02" 137 / 5.39"
S40A-80 62Kg/136.7lbs DN80 / 3" 37 / 44.4 318 / 12.52" 500 / 19.59" 142 / 5.59"
S40A-100 120Kg/264.5lbs DN100 / 4" 76 / 91.2 406 / 15.99" 521 / 20.52" 180 / 7.09"
S40A-150 170Kg/374.8lbs DN150 / 6" 260 / 312 559 / 22" 780 / 30.71" 220 / 8.66"
VALVE TECHNICAL DATA SHEET BOLTED BONNET CARTRIDGE VALVE - ANGLE PATTERN SERIES 40C

Bellows Sealed Angle Pattern Globe Valve, standard bore, outside screw and yoke, non-rising handwheel, bolted bonnet. To BSEN15761 or nuclear class to ASME III available.

Valve can be supplied with actuation - electric or pneumatic plus controls.

Extended spindles also available.

Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection or manifold blocks.

Cartridge valve, seat and all seals are removed with the top assembly. This leaves only the body left in line. Maintenance time reduced significantly.

Increases safety, no danger of seals being lost down line or seat not being fitted.

Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials. Valve seals suitable for temperatures up to 320 ℃. Materials can be changed to customer specifications.

Dimensions
Size
DN
Dim A
mm
Dim B
mm
Dim C
mm
Dim D
mm
Dim E
mm
Weight
Kg
8 45 200 32 101 102 8
15 57 218 32 101 102 12
20 64 230 32 101 102 12
25 70 230 32 127 102 12
40 83 235 43 155 128 21
50 102 255 51 155 165 26
80 178 482 104 254 220 202
100 203 502 114 254 240 275
150 279 770 139 450 278 355
Component Material
Body St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307) / ASME SA182 F304L
Bonnet St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307) / ASME SA182 F304L
Seat St.St. BSEN 10088-3 1.4307 / ASME SA479 304L
Seat Seal Perlast or Kalrez seal
Disk St.St. BSEN 10088-3 1.4307 / ASME SA479 304L
Stem St.St. BSEN 10088-3 1.4307
Bellows St.St. Type 316L
Back up Gland Graphite
CARTRDIGE VALVE TECHNICAL DATA SHEET
STOP AND STOP/CHECK VALVE SERIES 50A
103.4 Bar 1500 psi (Class 600)
Technical Data
Design SpecificationDEF STAN 02-375 and ANSI B16.34
Working Pressure 103.4 Bar / 1500 psi
Working Temperature Min -20 ℃/-4℉ - - Max 326 ℃/619℉
Applications    |    Medium Air, Oil, Gas, Water
Quality Assurance Level EN 10204, 3.1b also Full traceability - MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330 or MIL-STD-1622
Hydrostatic Test 156 Bar / 2262psi
Valve Closure Test 114 Bar / 1653psi
Shock QualificationTo be verified by test to customer's requirements e.g. MIL-S-901D
Vibration QualificationTo be verified by test to customer's requirements e.g. MIL-STD-167-1
Leakage ClassBubble Tight as per ANSI Class VI
Valve Body Material Forged Stainless Steel type 316L, Super Austenitic type F44, Carbon Steel type A105, Monel or Ni Al Br DEF STAN 02-833 pt2
Main Cartridge Components Material Stainless Steel type 316L, Super Austenitic type F44, Monel or Ni Al Br
Seals Material Perlast / Kalrez
Seat Material Stainless Steel type 316L, Super Austenitic type F44, Monel, PEEK or Ni Al Br
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASTM A193/ MIL-S-1222/Monel
Handwheel Material Aluminum, Stainless Steel or Iron
Connection Type Cartridge flanged to housing. Housing socket weld ends, buttweld ends or flanged
OVERALL DIMENSIONS (CARTRIDGE AND VALVE BODY)
Product
Designation
Estimated
Weight
Pipe Size CV
UK Gal/min / US Gal/min
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
S50A-15 5Kg/11lbs DN15 /1/2 " 2.45 / 2.94 108 / 4.26" 171 / 6.73" 108 / 4.26"
S50A-20 7Kg/15.5lbs DN20/3/4" 2.45 / 2.94 117 / 4.61" 171 / 6.73" 108 / 4.26"
S50A-25 8Kg/17.6lbs DN25 / 1" 5.8 / 6.96 127 / 5" 185 / 7.28" 108 / 4.26"
S50A-40 10Kg/22lbs DN40 /11/2" 12.4 / 14.9 165 / 6.5" 190 / 7.48" 115 / 4.53"
S50A-50 16.5Kg/36.4lbs DN50 / 2" 18.5 / 22.2 203 / 8" 250 / 9.84" 115 / 4.53"
S50A-80 56Kg/123.4lbs DN80 / 3" 37 / 44.4 318 / 12.52" 340 / 13.4" 142 / 5.59"
S50A-100 90Kg/198.5lbs DN100 / 4" 76 / 91.2 406 / 15.99" 370 / 13.57" 180 / 7.09"
S50A-150 140Kg/308.6lbs DN150 / 6" 260 / 312 559 / 22" 540 / 21.26" 220 / 8.66"
CARTRDIGE VALVE TECHNICAL DATA SHEET
STOP AND STOP/CHECK VALVE SERIES 50B
103.4 Bar 1500 psi (Class 600)
Technical Data
Design SpecificationDEF STAN 02-375 and ANSI B16.34
Working Pressure 103.4 Bar / 1500 psi
Working Temperature Min -20 ℃/-4℉ - - Max 326 ℃/619℉
Applications    |    Medium Air, Oil, Gas, Water
Quality Assurance Level EN 10204, 3.1b also Full traceability - MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330 or MIL-STD-1622
Hydrostatic Test 156 Bar / 2262psi
Valve Closure Test 114 Bar / 1653psi
Shock QualificationTo be verified by test to customer's requirements e.g. MIL-S-901D
Vibration QualificationTo be verified by test to customer's requirements e.g. MIL-STD-167-1
Leakage ClassBubble Tight as per ANSI Class VI
Valve Body Material Forged Stainless Steel type 316L, Super Austenitic type F44, Carbon Steel type A105, Monel or Ni Al Br DEF STAN 02-833 pt2
Main Cartridge Components Material Stainless Steel type 316L, Super Austenitic type F44, Monel or Ni Al Br
Seals Material Perlast / Kalrez
Seat Material Stainless Steel type 316L, Super Austenitic type F44, Monel, PEEK or Ni Al Br
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASTM A193/ MIL-S-1222/Monel
Handwheel Material Aluminum, Stainless Steel or Iron
Connection Type Cartridge flanged to housing. Housing socket weld ends, buttweld ends or flanged
OVERALL DIMENSIONS (CARTRIDGE AND VALVE BODY)
Product
Designation
Estimated
Weight
Pipe Size CV
UK Gal/min / US Gal/min
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
S50A-15 5Kg/11lbs DN15 /1/2 " 2.45 / 2.94 108 / 4.26" 171 / 6.73" 108 / 4.26"
S50A-20 7Kg/15.5lbs DN20/3/4" 2.45 / 2.94 117 / 4.61" 171 / 6.73" 108 / 4.26"
S50A-25 8Kg/17.6lbs DN25 / 1" 5.8 / 6.96 127 / 5" 185 / 7.28" 108 / 4.26"
S50A-40 10Kg/22lbs DN40 /11/2" 12.4 / 14.9 165 / 6.5" 190 / 7.48" 115 / 4.53"
S50A-50 16.5Kg/36.4lbs DN50 / 2" 18.5 / 22.2 203 / 8" 250 / 9.84" 115 / 4.53"
S50A-80 56Kg/123.4lbs DN80 / 3" 37 / 44.4 318 / 12.52" 340 / 13.4" 142 / 5.59"
S50A-100 90Kg/198.5lbs DN100 / 4" 76 / 91.2 406 / 15.99" 370 / 13.57" 180 / 7.09"
S50A-150 140Kg/308.6lbs DN150 / 6" 260 / 312 559 / 22" 540 / 21.26" 220 / 8.66"
VALVE TECHNICAL DATASHEET NON-BELLOWS SEALED VALVE - ANGLE PATTERN GLOBE SERIES 50C

Angle Pattern Globe

Class 800 gland sealed globe valve to BS5352, standard bore, outside screw and yoke, non-rising handwheel, bolted bonnet.

Available with integral hard faced seat or screwed in stainless steel seat.

Valve can be supplied with actuator - electric or pneumatic.

Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection.

Nuclear versions to ASME III available.?

Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials.

Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425 ℃.

If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Dimensions
Size
DN
Dim
A mm
Dim
B mm
Dim
C mm
Weight
Kg
Cv
UKGPM
6 57 241 100 9 2.7
15 57 241 100 9 3.9
20 64 241 100 9 3.9
25 70 254 100 9.6 9.2
40 83 368 150 24 19.8
50 102 400 150 25 29.6
Material
Component Carbon Steel Valve Stainless Steel Valve
Body & Bonnet C.St. ASTM A105 St.St. Type 316L
Seat St.St. Type 410 or integral Stellite HF St.St. Type 410 or integral Stellite HF
Disk St.St. Type 410 or Stellite HF St.St. Type 410 or Stellite HF
Stem St.St. Type 316L St.St. Type 316L
Back up Gland Exfoliated Graphite Exfoliated Graphite
Yoke Bush Aluminium Bronze Aluminium Bronze
VALVE TECHNICAL DATASHEET NON-BELLOWS SEALED VALVE - STRAIGHT PATTERN NON-RETURN SERIES 50D

Class 800 non-return valve to BS5352, standard bore, bolted bonnet.

Available with integral hard faced seat or screwed in stainless steel seat.

Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection

Dimensions
Size
DN
Dim
A mm
Dim
B mm
Weight
Kg
Cv
UKGPM
6 108 170 3 1.7
15 108 170 3 2.45
20 117 190 3 2.45
25 127 190 4.5 5.8
40 165 220 12 12.4
50 203 400 15 18.5

Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials. Shown are the maximum ratings for socket weld, butt weld and screwed ends to BS5352.

Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St.

ASTM A105 is not recommended for use above 425 oC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Material
Component Carbon Steel Valve Stainless Steel Valve
Body C.St. ASTM A105 St.St. BS1503 304S11
Bonnet C.St. ASTM A105 St.St. BS1503 304S11
Seat St.St. Type 410 or integral Stellite HF St.St. Type 410 or integral Stellite HF
Disk St.St. Type 410 or Stellite HF St.St. Type 410 or Stellite HF
Service Temperature ℃ Service Pressure bar g
-38 to +38 99
50 98
100 96
150 94
200 91
250 87
300 79
350 71
400 63
450 55
500 34

--- 77 ---

CARTRIDGE VALVE TECHNICAL DATA SHEET
CHECK VALVE SERIES 50D1
103.4 Bar 1500 psi (Class 600)
Technical Data
Design SpecificationDEF STAN 02-375 and ANSI B16.34
Working Pressure 103.4 Bar / 1500 psi
Working Temperature Min -20 ℃/-4℉ - - Max 326 ℃/619℉
Applications    |    Medium Air, Oil, Gas, Water
Quality Assurance Level EN 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330 or MIL-STD-1622
Hydrostatic Test 156 Bar / 2262psi
Valve Closure Test 114 Bar / 1653psi
Shock QualificationTo be verified by test to customer’s requirements e.g. MIL-S-901D
Vibration QualificationTo be verified by test to customer’s requirements e.g. MIL-STD-167-1
Leakage ClassBubble Tight as per ANSI Class VI
Valve Body Material Forged Stainless Steel type 316L, Super Austenitic type F44, Carbon Steel type A105, Monel or Ni Al Br DEF STAN 02-833 pt2
Main Cartridge Components Material Stainless Steel type 316L, Super Austenitic type F44, Monel or Ni Al Br
Seals Material Perlast / Kalrez
Seat Material Stainless Steel type 316L, Super Austenitic type F44, Monel, PEEK or Ni Al Br
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASTM A193/ MIL-S-1222/Monel
Connection Type Cartridge flanged to housing. Housing socket weld ends, buttweld ends or flanged
OVERALL DIMENSIONS (CARTRIDGE AND VALVE BODY)
Product
Designation
Estimated
Weight
Pipe Size CV
UK Gal/min / US Gal/min
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
S50D1-15 5Kg/11lbs DN15 /1/2 " 2.45 / 2.94 108 / 4.26" 128 / 5.04" 108 / 4.26"
S50D1-20 7Kg/15.5lbs DN20/3/4" 2.45 / 2.94 117 / 4.61" 171 / 6.73" 108 / 4.26"
S50D1-25 8Kg/17.6lbs DN25 / 1" 5.8 / 6.96 127 / 5" 185 / 7.28" 108 / 4.26"
S50D1-40 10Kg/22lbs DN40 /11/2" 12.4 / 14.9 165 / 6.5" 126 / 4.96" 115 / 4.53"
S50D1-50 16.5Kg/36.4lbs DN50 / 2" 18.5 / 22.2 203 / 8" 207 / 8.15" 115 / 4.53"
S50D1-80 46Kg/101lbs DN80 / 3" 37 / 44.4 318 / 12.52" 225 / 8.86" 142 / 5.59"
S50D1-100 55Kg/121lbs DN100 / 4" 76 / 91.2 406 / 15.99" 208 / 8.19" 180 / 7.09"
S50D1-150 95Kg/209lbs DN150 / 6" 260 / 312 559 / 22" 320 / 12.6" 220 / 8.66"
CARTRIDGE VALVE TECHNICAL DATA SHEET
CHECK VALVE SERIES 50D2
103.4 Bar 1500 psi (Class 600)
Technical Data
Design SpecificationDEF STAN 02-375 and ANSI B16.34
Working Pressure 103.4 Bar / 1500 psi
Working Temperature Min -20 ℃/-4℉ - - Max 326 ℃/619℉
Applications    |    Medium Air, Oil, Gas, Water
Quality Assurance Level EN 10204, 3.1b also Full traceability – MIC Level 1
Cleaning TP102, Oxygen cleaning to MIL-STD-1330 or MIL-STD-1622
Hydrostatic Test 156 Bar / 2262psi
Valve Closure Test 114 Bar / 1653psi
Shock Qualification To be verified by test to customer’s requirements e.g. MIL-S-901D
Vibration Qualification To be verified by test to customer’s requirements e.g. MIL-STD-167-1
Leakage ClassBubble Tight as per ANSI Class VI
Valve Body Material Forged Stainless Steel type 316L, Super Austenitic type F44, Carbon Steel type A105, Monel or Ni Al Br DEF STAN 02-833 pt2
Main Cartridge Components Material Stainless Steel type 316L, Super Austenitic type F44, Monel or Ni Al Br
Seals Material Perlast / Kalrez
Seat Material Stainless Steel type 316L, Super Austenitic type F44, Monel, PEEK or Ni Al Br
Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASTM A193/ MIL-S-1222/Monel
Connection Type Cartridge flanged to housing. Housing socket weld ends, buttweld ends or flanged
S50D2-25 8.6Kg/18.9lbs DN25 / 1” 11 / 13.2 216 / 8.5” 100 / 3.94” 86 / 3.39”
OVERALL DIMENSIONS (CARTRIDGE AND VALVE BODY)
Product
Designation
Estimated
Weight
Pipe Size CV
UK Gal/min / US Gal/min
A
(mm/ins)
B
(mm/ins)
C
(mm/ins)
S50D2-15 6Kg/13.2lbs DN15 /1/2 " 5.8 / 6.96 165 / 6.5" 100 / 3.94" 86 / 3.39"
S50D2-20 6Kg/13.2lbs DN20/3/4" 5.8 / 6.96 190 / 7.48" 100 / 3.94" 86 / 3.39"
S50D1-25 8Kg/17.6lbs DN25 / 1" 5.8 / 6.96 127 / 5" 185 / 7.28" 108 / 4.26"
S50D1-40 10Kg/22lbs DN40 /11/2" 12.4 / 14.9 165 / 6.5" 126 / 4.96" 115 / 4.53"
S50D1-50 16.5Kg/36.4lbs DN50 / 2" 18.5 / 22.2 203 / 8" 207 / 8.15" 115 / 4.53"
S50D1-80 46Kg/101lbs DN80 / 3" 37 / 44.4 318 / 12.52" 225 / 8.86" 142 / 5.59"
S50D1-100 55Kg/121lbs DN100 / 4" 76 / 91.2 406 / 15.99" 208 / 8.19" 180 / 7.09"
S50D1-150 95Kg/209lbs DN150 / 6" 260 / 312 559 / 22" 320 / 12.6" 220 / 8.66"
VALVE TECHNICAL DATASHEET INSTRMENT VALVE - STRAIGHT PATTERN SERIES 55A

Class 600 bellows sealed globe valve, standard bore, outside screw and yoke, non-rising handwheel, union bonnet

Available with integral seat or screwed in stainless steel seat or soft seated with O ring in disk

Valve can be supplied with pneumatic actuator Butt weld end connections shown, also available as screwed, socket weld, flanged or any special connection.

Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials.

Materials can be changed to customer specifications.

There are temperature restrictions on some materials, ie. C.st. ASTM A105 is not recommended for use above 425 ℃. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Dimensions
Size
DN
Dim
A mm
Dim
B mm
Dim
C mm
Weight
Kg
6 101.6 180 100 3.5
10 101.6 180 100 3.5
15 108 190 100 4
20 117 195 100 4
25 127 200 100 4.5
Component Material
Body St.St. Type 316L
Bonnet St.St. Type 316L
Seat St.St. Type 316L or integral
Disk St.St. Type 316L with/without Viton seal
Stem St.St. Type 316L
Gland Bush St.St. Type 316L
Back up Gland PTFE
Yoke Bush Aluminium Bronze
VALVE TECHNICAL DATASHEET LIQUID METAL BELLOW SEALED GLOBE VALVE LIP-SEAL WELDED BONNET

Class 900 Bellows Sealed Globe Valve, Conventional Bore, Outside Screw and Yoke, Bolted and lip-seal welded Bonnet. ASME III option available.

Secondary Gland in the event of bellows failure.

Available with Integral Hard Faced Seat to offer increased resistance against erosion.

Valve can be supplied with manual operation or Actuated - Electric or Pneumatic.

Manual Valve and Electrically Actuated Valve shown

Manually Operated Electrically Actuated
Size
DN/NPS
Length A
mm/in
Height B
mm/in
Weight
Kg/lb
Height D
mm/in
Length E
mm/in
Weight
Kg/lb
Cv
IGPM/USGPM
DN8/3/8" 288/11.34 245/9.65 13.8/30.5 551/21.7 245/9.65 Please Ask For Details 7/8.4
DN15/1/2" 288/11.34 245/9.65 13.8/30.5 551/21.7 245/9.65 7/8.4
DN20/3/4" 288/11.34 245/9.65 13.8/30.5 551/21.7 245/9.65 12.9/15.4
DN25/1" 288/11.34 245/9.65 13.8/30.5 551/217 245/9.65 20.8/25
DN40/11/2" 323/12.72 293/11.54 24.1/53.1 585/23.03 293/11.54 39/46.8
DN50/2" 407/16.03 311/12.25 46.8/103 605/23.8 311/12.25 92/110
DN65/21/2" 407/16.03 311/12.25 46.8/103 605/23.8 311/12.25 125/150
DN80/3" 437/17.2 420/16.54 97.7/215 742/29.2 420/16.54 213/255
DN100/4" 427/16.82 443/17.45 183/403 775/30.5 443/17.45 260/312
Materials
316 Stainless Steel 304 Stainless Steel
Body St.St. ASME SA182 F316 304 Stainless Steel
Bonnet St.St. ASME SA182 F316 St.St. ASME SA182 F304
Seat St.St. ASME SA479 F316 or Integral Stellite hard faced St.St. ASME SA479 F304 or Integral Stellite hard faced
Disk St.St. ASME SA479 F316 or St.St. Type 316 hard faced St.St. ASME SA479 F304or St.St. Type 304 hard faced
Stem St.St. ASME SA479 F316 St.St. ASME SA479 F304
Bellows St.St. Type 316/316L St.St. Type 316/316L
Back up Gland Exfoliated Graphite Exfoliated Graphite
Yoke Bush Aluminium Bronze Aluminum Bronze

Valve Shown is with a leak detection port, to provide early warning of any bellows failure.

Extended Spindles, type and length are designed to suit customer requirements.

Weights shown are without extended spindle. Pneumatically Actuated valvesare available.

VALVE TECHNICAL DATA SHEET LIQUID METAL BELLOW SEALED GLOBE VALVE LIP-SEAL WELDED BONNET -EXTENDED SPINDLE

Class 900 Bellows Sealed Globe Valve, Conventional Bore, Outside Screw and Yoke, Bolted and lip-seal welded Bonnet, with universal joint extended spindle. ASME III option available.

Secondary Gland in the event of bellows failure. Available with Integral Hard Faced Seat to offer increased resistance against erosion.

Valve can be supplied with manual operation or Actuated - Electric or Pneumatic. Manual Valve shown

Dimensions (typical)
Size
DN/NPS
Length
A mm/in
Weight
Kg/lb I
Cv
GPM/USGPM
DN8/3/8" 288/11.34 13.8/30.5 7/8.4
DN15/1/2" 288/11.34 13.8/30.5 7/8.4
DN20/3/4" 288/11.34 13.8/30.5 12.9/15.4
DN25/1" 288/11.34 13.8/30.5 20.8/25
DN40/11/2" 323/12.72 24.1/53.1 39/46.8
DN50/2" 407/16.03 46.8/103 92/110
DN65/21/2" 407/16.03 46.8/103 125/150
DN80/3" 437/17.2 97.7/215 213/255
DN100/4" 427/16.82 183/403 260/312
Material
316 Stainless Steel 304 Stainless Steel
Body St.St. ASME SA182 F316 St.St. ASME SA182 F304
Bonnet St.St. ASME SA182 F316 St.St. ASME SA182 F304
Seat St.St. ASME SA479 F316 or Integral Stellite hard faced St.St. ASME SA479 F304 or Integral Stellite hard faced
Disk St.St. ASME SA479 316 or St.St. Type 316 hard faced St.St. ASME SA479 F304 or St.St. Type 304 hard faced
Stem St.St. ASTM A182 F316 St.St. ASTM A182 F304
Bellows St.St. Type 316 St.St. Type 316
Back up Gland Exfoliated graphite Exfoliated Graphite
Yoke Bush Aluminium Bronze Aluminium Bronze

Valve Shown is with a leak detection port, to provide early warning of any bellows failure.

Extended Spindles, type and length are designed to suit customer requirements. Weights shown are without extended spindle.

Extended spindle shown is with intermediate seal/support at the bulge wall level. Design without intermediate stage are available.

VALVE TECHNICAL DATA SHEET BELLOWS SEALED CARTRIDGE VALVE - NUCLEAR CLASS 200

Class 2500 Bellows Sealed Globe Valve designed to ASME III, Conventional Bore, Outside Screw andYoke, Non-rising Handwheel, Bolted Bonnet.

Seal Welded Bonnet version available. Also available with Integral Hard Faced Seat or Screwed in Stainless Steel Seat.

Valve can be supplied with Actuator - Electric or Pneumatic.

Buttweld end connections shown, also available as screwed, socket weld, Flanged or special connection Cartridge Valve, seat and all seals are removed with the top assembly.This leaves only body left in line.

Maintainence time reduced significantly. Increases safety, no danger of seals being lost down line or seat not being fitted. Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Dimensions (typical)
Valve Size
DN
Dim
A in
Dim
B in
Weight
lb
Cv
IGPM
DN8/1/4" 10.4" 19.69" 29.9 0.6
DN15/1/2" " " 29.9 1.5
DN20/3/4" 10.4" 19.69" 32.66 2.4
DN25/1" 10.75" 20.07" 35.38 5
DN40/11/2" 12.13" 21.38" 40.82 12
" 15.12" 23.70" 49.9 21
Material
316 Stainless Steel 304 Stainless Steel
Body St.St. ASME SA182 F316 St.St. ASME SA182 F304
Bonnet St.St. ASME SA182 F316 St.St. ASME SA182 F304
Seat St.St. ASME SA479 F316 or Integral Stellite hard faced St.St. ASME SA479 F304 or Integral Stellite hard faced
Disk St.St. ASME SA479 316 or St.St. Type 316 hard faced St.St. ASME SA479 F304 or St.St. Type 304 hard faced
Stem St.St. ASTM A182 F316 St.St. ASTM A182 F304
Bellows St.St. Type 316 St.St. Type 316
Back up Gland Exfoliated graphite Exfoliated Graphite
Yoke Bush Aluminium Bronze Aluminium Bronze
VALVE TECHNICAL DATA SHEETS Index Page
Valve
Datasheet
Number
Title Description Application Variants
1 HIGH TEMPERATURE
BELLOWS SEALED VALVE
SERIES 4
Bellows Sealed Globe Valve Straight Pattern for high temperature applications

Nuclear Power Plants, Marine Applications, Petrochemical Plants, Titanium Production Plant, Magnesium Refining Plant, Rocket Engine Test Facilities

  • Propulsion System
  • CO2 Cooling Circuits
  • Primary Heat Transport
  • Fuel Handling Systems
  • Radioactive Waste Water
  • Decay Stores Containment
  • Contaminated Stream Containment
  • Nitric Acid Containment
  • Pond Boron Monitoring System
  • Liquid Sodium/Potassium 'Alloy' Circuits Liquid Hydrogen Fuelling Circuit

'Alloy' Circuits Liquid Hydrogen Fuelling Circuit

Variants - B
2 BELLOWS SEALED CARTRIDGE VALVEMANIFOLD
SERIES 34
Bellows Sealed Cartridge valves in example manifold block Variants - A
3 BELLOWS SEALED CARTRIDGE VALVE
SERIES 34
Bellows Sealed Cartridge valves in example manifold block Variants - A
4 BELLOWS SEALED VALVE
SERIES 34
Bellows Sealed Globe Valve Straight Pattern Seal welded Bonnet Variants - B
5 BELLOWS SEALED VALVE
SERIES 34
Bellows Sealed Globe Valve Straight Pattern Bolted Bonnet Variants - B
6 BELLOWS SEALED VALVE NUCLEAR
SERIES 34
Bellows Sealed Globe Valve Straight Pattern Bolted Bonnet to ASME III Variants - B
7 BELLOWS SEALED CARTRIDGE VALVE EXTREME
SERIES 34
Bellows Sealed Globe Straight Pattern Cartridge Valve. For extreme duties Variants - A
8 HIGH TEMPERATURE BELLOWS SEALED VALVE
SERIES 34
Bellows Sealed Globe Valve Straight Pattern for high temperature applications Variants - B
9 BOLTED BONNET VALVE - STRAIGHT PATTERN
SERIES 34A
Bellows Sealed Globe Valve Straight Pattern Bolted Bonnet Variants - B
10 BOLTED BONNET VALVE - OBLIQUE PATTERN
SERIES 34B
Bellows Sealed Globe Valve Y Pattern Bolted Bonnet Variants - B
11 BOLTED BONNET VALVE - ANGLE PATTERN
SERIES 34C
Bellows Sealed Globe Valve Angle Pattern Bolted Bonnet Variants - B
12 SEAL WELDED BONNET VALVE - STRAIGHT PATTERN
SERIES 35A
Bellows Sealed Globe Valve Straight Pattern Seal welded Bonnet Variants - B
13 SEAL WELDED BONNET VALVE - OBLIQUE PATTERN
SERIES 35B
Bellows Sealed Globe Valve Straight Pattern Seal welded Bonnet Variants - B
VALVE TECHNICAL DATA SHEETS Index Page
Valve
Datasheet
Number
Title Description Application Variants
14 SEAL WELDED BONNET VALVE -ANGLE PATTERN
SERIES 35C
Bellows Sealed Globe Valve Angle Pattern Seal welded Bonnet

Nuclear Power Plants, Marine Applications, Petrochemical Plants, Titanium Production Plant, Magnesium Refining Plant, Rocket Engine Test Facilities

  • Propulsion System
  • CO2 Cooling Circuits
  • Primary Heat Transport
  • Fuel Handling Systems
  • Radioactive Waste Water
  • Decay Stores Containment
  • Contaminated Stream Containment
  • Nitric Acid Containment
  • Pond Boron Monitoring System
  • Liquid Sodium/Potassium 'Alloy' Circuits Liquid Hydrogen Fuelling Circuit

'Alloy' Circuits Liquid Hydrogen Fuelling Circuit

Variants - B
15 BOLTED/EDGE WELDED BONNET VALVE - STRAIGHT PATTERN
SERIES 36A
Bellows Sealed Globe Valve Straight Pattern Bolted / Edge welded Bonnet Variants - B
16 BOLTED/EDGE WELDED BONNET VALVE - OBLIQUE PATTERN
SERIES 36B
Bellows Sealed Globe Valve Y Pattern Bolted / Edge welded Bonnet Variants - B
17 BOLTED/EDGE WELDED BONNET VALVE -ANGLE PATTERN
-SERIES 36C
Bellows Sealed Globe Valve Angle Pattern Bolted / Edge welded Bonnet Variants - B
18 BELLOWS SEALED STOP AND STOP/CHECK VALVE
SERIES 40A
Bellows Sealed Globe Straight Pattern Cartridge Valve. Stop valve and Stop check options Variants - A
19 BELLOWS SEALED STOP AND STOP/CHECK VALVE
SERIES 40B
Bellows Sealed Globe Y Pattern Cartridge Valve. Stop valve and Stop check options Variants - A
20 BOLTED BONNET CARTRIDGE VALVE - ANGLE PATTERN
SERIES 40C
Bellows Sealed Globe Angle Pattern Cartridge Valve. Variants - A
21 STOP AND STOP/CHECK VALVE
SERIES 50A
Globe Straight Pattern Cartridge Valve. Stop valve and Stop check options Variants - A
22 STOP AND STOP/CHECK VALVE
SERIES 50B
Globe Y Pattern Cartridge Valve. Stop valve and Stop check options Variants - A
23 NON-BELLOWS SEALED VALVE -ANGLE PATTERN GLOBE -
SERIES 50C
Globe Angle Pattern Cartridge Valve. Stop valve Variants - A
24 NON-BELLOWS SEALED VALVE -STRAIGHT PATTERN NON-RETURN
SERIES 50D
Globe Straight Pattern Piston Check Valve Variants - C
25 CHECK VALVE SERIES 50D1 Globe Straight Pattern Piston Check Cartridge Valve. Stop valve and Stop check options Variants - D
VALVE TECHNICAL DATA SHEETS Index Page
Valve
Datasheet
Number
Title Description Application Variants
26 CHECK VALVE
SERIES 50D2
Globe Y Pattern Piston Check Cartridge Valve. Stop valve and Stop check options

Nuclear Power Plants, Marine Applications, Petrochemical Plants, Titanium Production Plant, Magnesium Refining Plant, Rocket Engine Test Facilities

  • Propulsion System
  • CO2 Cooling Circuits
  • Primary Heat Transport
  • Fuel Handling Systems
  • Radioactive Waste Water
  • Decay Stores Containment
  • Contaminated Stream Containment
  • Nitric Acid Containment
  • Pond Boron Monitoring System
  • Liquid Sodium/Potassium 'Alloy' Circuits Liquid Hydrogen Fuelling Circuit

'Alloy' Circuits Liquid Hydrogen Fuelling Circuit

Variants - D
27 INSTRUMENT VALVE - STRAIGHT PATTERN
SERIES 55A
Instrument Valve straight pattern union bonnet Variants - B
28 LIQUID METAL BELLOW SEALED GLOBE VALVE - LIP-SEAL WELDED BONNET Bellows Sealed Globe Valve Y Pattern Bolted / Edge welded Bonnet for liquid metal applications Variants - B
29 LIQUID METAL BELLOW SEALED GLOBE VALVE - LIP-SEAL WELDED BONNET
-EXTENDED SPINDLE
Bellows Sealed Globe Valve Y Pattern Bolted / Edge welded Bonnet with extended spindle for liquid metal applications Variants - B
30 CLASS 2500 BELLOWS SEALED CARTRIDGE VALVE
-NUCLEAR
Bellows Sealed Cartridge Valve Straight Pattern Bolted Bonnet for high pressure applications Variants - A
Bespoke versions to Customer Specifications can be Developed - Talk to Manufacturer

Variants - A:

Nuclear to ASME III Class I, II or III.

Non-cartridge Seal Welded Bonnet for Liquid Metal Applications.

Non-Cartridge Cryogenic version with/without vacuum jacket.

Soft seat, metal seat, hard faced seat and integral seat options.

Electric, Pneumatic or Hydraulic actuation.

Bespoke End Connections.

Extended Spindle to remove handwheel (or actuator)from Hot/Cold or active area.

Variants - B:

Nuclear to ASME III Class I, II or III.

Cartridge Version

Cartridge Cryogenic version with/without vacuum jacket.

Soft seat, metal seat, hard faced seat and integral seat options.

Electric, Pneumatic or Hydraulic actuation.

Bespoke End Connections.

Extended Spindle to remove handwheel (or actuator) from Hot/ Cold or active area.

Variants - C:

Nuclear to ASME III Class I, II or III.

Cartridge Version

Soft seat, metal seat, hard faced seat and integral seat options.

Bespoke End Connections.

Tight shut-off at low pressure version available.

Variants - D:

Nuclear to ASME III Class I, II or III.

Non-cartridge Seal Welded Bonnet for Liquid Metal Applications.

Soft seat, metal seat, hard faced seat and integral seat options.

Bespoke End Connections.

Tight shut-off at low pressure version available.